If you’ve ever stood in a valve assembly room, or sat in on a client discussion about specifying the right valve for a high-pressure pipeline, chances are someone has asked the difference between trunnion and floating ball valves. As a pneumatic ball valve supplier, I get this question almost weekly—and I don’t blame folks for being confused. At first glance, both look like simple ball valves: a round bore, a quarter-turn rotation, a lever or actuator to open and close. Dig a little, though, and their internal designs, performance, and ideal use cases are worlds apart. Pneumatic Ball Valve

I started working with pneumatic ball valves right out of technical sales training, and my first big mistake was recommending a floating ball valve for a 900-psi natural gas line. A client came back a week later with a leaking seal, and it took me hours to trace the problem to that basic design difference. That experience stuck with me, and it’s why I never skip walking through the actual mechanics that set these two valves apart.
Let’s start with the basics, no jargon overload. A standard ball valve’s core is a hollow, perforated ball that rotates 90 degrees—turn it parallel to the pipe and flow opens, turn it perpendicular and flow stops. That’s the same for both trunnion and floating ball valves. The difference is how that ball is held in place, and how the seal around it works.
Floating ball valves get their name because the ball is not rigidly supported; it “floats” between two seats, usually PTFE or another soft elastomer. That sounds simple, but that float is a key functional part. When pressure builds on the upstream side of the valve, it pushes the ball hard against the downstream seat. That pressure actually creates a tighter seal, right? It’s a simple, self-energizing design. But that same floating feature is a limit. For low-pressure, low-volume applications, that’s fine. You’ll see these on residential water lines, small steam lines, or mild industrial fluid transfers—places where pressure rarely tops 300 psi.
Trunnion ball valves, on the other hand, have two rigid supports, called trunnions, that stick out from the top and bottom of the ball. These trunnions hold the ball firmly in place, so it doesn’t move even when high pressure hits it. That changes everything. First, the seats here don’t rely on the ball’s float for a seal. Instead, spring-loaded or pressure-energized seats press against the ball, creating a tight barrier even at 1,500 psi or more. That’s why trunnion valves are the go-to for high-pressure pipelines, oil and gas drilling, or cryogenic applications where temperatures swing wildly.
Wait, let’s dig into pressure and force, because that’s where the trade-offs become clear. With a floating ball valve, the force from media pressure pushes the ball against one seat. The seat has to resist that force, and that works well until the pressure gets too high. Once pressure crosses a threshold, the force can become so great that the seat deforms, leaks, or even causes the valve actuator to work too hard. I’ve seen small floating valves bind up because the 500-psi gas line pushed the ball against the seat, creating friction that the pneumatic actuator couldn’t overcome. That’s not a failure of the actuator—it’s a design limitation.
Trunnion valves distribute that pressure force across the trunnions, not just on the seats. The trunnions bear the weight and pressure load, so the seats only need to maintain a seal, not hold back the full line pressure. That means the seats can be smaller, or made of more durable materials, and the actuator doesn’t have to work as hard. For pneumatic actuators specifically, that’s a big deal. A smaller, more cost-effective actuator can run a trunnion valve at 1,000 psi, whereas a floating valve at the same pressure would need a much larger actuator, driving up cost and energy use.
Size matters, too. Floating ball valves are almost always smaller—we’re talking 2-inch diameter and below, usually. Above that, the floating ball gets too heavy, and the pressure force becomes too much for the seats to handle. A 6-inch floating ball valve would struggle with even 200 psi, because the ball’s weight plus the pressure pushing it against the seat would cause excessive wear and leakage. Trunnion valves, though, are made in sizes up to 48 inches and beyond, perfect for large pipeline networks where flow volume is massive.
Then there’s the question of end connections and extreme conditions. Trunnion ball valves are designed for tough environments: cryogenic services where PTFE seats would become brittle, high-temperature applications where elastomers can soften, and media that’s abrasive or corrosive. The trunnion support keeps the ball aligned, so even if the valve expands slightly with heat, it doesn’t bind or lose its seal. I sold a set of trunnion pneumatic ball valves last year for a chemical plant handling 350-degree caustic soda—those floating valves I messed up years ago would have failed in a week, but the trunnion ones have been running for 18 months with zero leaks.
Floating valves, by contrast, are built for milder, shorter-cycle use. They’re cheaper to manufacture, lighter, and easier to install, so they’re common in HVAC systems, food and beverage processing (where cleanliness is key and pressure is low), and small process skids. If you’re building a skid for a pilot project that runs at 150 psi, a floating valve is a smart choice—no need to overspec, and you’ll save on upfront cost.
Wait, what about leakage rates? That’s a big one for many clients. Both valves are designed to meet industry standards, but trunnion valves can achieve bubble-tight leakage even at high pressure, whereas floating valves might have slightly higher leakage at their upper pressure limit. That’s because the trunnion design allows for more precise seat adjustment. For applications where zero leakage is non-negotiable—like natural gas pipelines, hydrogen transport, or pharmaceutical fluid lines—trunnion is almost always the pick. Floating valves work for applications where minor external or seat leakage is acceptable, like general water distribution.
Let’s talk about maintenance, because that’s a practical point no one wants to ignore. Floating ball valves are simpler to service, right? You can usually remove the actuator and the top bonnet, pull the ball out, and replace the seats without taking the whole valve out of the line. Trunnion valves require more work—you have to align the trunnions properly when you reassemble, and the seats are often integrated with the trunnion supports, so servicing takes longer and needs more technical expertise. That’s another trade-off: trunnion valves are more robust, but they’re less user-friendly for on-the-fly repairs, which is something to factor in if your team does regular field servicing.
I get asked a lot: “Which one is better?” and the answer is always, “It depends.” There’s no one-size-fits-all. If you’re working with pneumatic ball valves for low-pressure, small-bore, low-cycle use, floating is fine. If you’re dealing with high pressure, large sizes, extreme temperatures, or critical leak-tight requirements, trunnion is the only reliable option.
Let me circle back to that first mistake I made. I used a floating valve on a 900-psi natural gas line because the client initially said pressure was “around 500 psi.” When we tested it at full pressure, the seat deformed. I learned that the key is to confirm the design parameters before spec’ing. That’s why as a pneumatic ball valve supplier, I always ask clients for more than just “what size and what media.” I need to know operating pressure, temperature, cycle count, whether the line is critical, and if maintenance is done in-house.
For example, if you’re a small manufacturing plant with a 3-inch compressed air line running at 125 psi, a floating ball valve with a pneumatic actuator will work perfectly, and it’s a third cheaper upfront. But if you’re a midstream oil company moving crude through a 12-inch line at 1,200 psi, a trunnion valve is non-negotiable—you can’t risk a catastrophic leak that would shut down the pipeline for days.
Another point: pressure drop. Because trunnion valves don’t rely on the ball pushing against a seat, their bore is almost full-sized, so pressure drop is lower. That means you use less energy to push fluid through the line, which saves money over time. Floating valves often have a slightly smaller effective bore because the ball is pushed so hard against the seat, creating a small restriction. For long pipelines, that pressure drop adds up, so trunnion valves are more energy-efficient.
I’ve also seen clients mix them up for the wrong reasons. A friend who runs a food processing plant once tried to use a trunnion valve for a soda line because he thought it was “more heavy-duty.” It worked, but it cost twice as much, and it was harder to clean because the trunnion design has more crevices where bacteria can grow. That’s a case where a floating valve would have been better—easier to sanitize, lower cost, and perfect for the 100 psi pressure of his carbonation line.
So how do you spot which is which when you’re looking at a valve? It’s not just the label. If you can see the top of the ball, floating valves have a smooth top without any protruding trunnion. Trunnion valves have a small shaft sticking out the top (and usually the bottom) that the actuator connects to. That’s a quick visual check—no need to crack open the valve.
At the end of the day, the difference between trunnion and floating ball valves comes down to trade-offs: cost vs. performance, simplicity vs. robustness, low pressure vs. high pressure. As a pneumatic ball valve supplier, my job isn’t to sell you the most expensive valve—it’s to help you pick the one that fits your exact application, so you don’t end up with a valve that leaks, binds, or fails before its time.

If you’re working on a project and aren’t sure which valve is right for you, we’d be happy to walk through your specs, answer questions, and help you find the perfect solution. Whether you need a small floating valve for a pilot skid or a heavy-duty trunnion valve for a high-pressure pipeline, we have the expertise and products to fit your needs. Don’t hesitate to reach out to discuss your requirements.
Flanged Trunnion Ball Valve References
- Valve Engineering Handbook. American Water Works Association, 2021.
- Process Piping Valves: Selection, Application, and Maintenance. ASME Press, 2019.
- “Ball Valve Design Fundamentals.” Valve Manufacturers Association of America (VMA) Technical Paper, 2020.
Zhejiang Bergamo Technology Co., Ltd.
As one of the most professional pneumatic ball valve manufacturers and suppliers in China, our products have good reputation in the market. Please feel free to wholesale durable pneumatic ball valve for sale here from our factory. Quality products and reasonable price are available.
Address: No.5 workshop, No.807 Jiulong Street, Bihu Town, Liandu District, Lishui, Zhejiang 323000 People’s Republic of China
E-mail: sales@bjm-valve.com
WebSite: https://www.bjmvalve.com/